Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Fishtown Homeowners
Fishtown‘s rowhouses were built for wood heat, and most of those chimneys are still topped with whatever was set there decades ago. A cracked crown or a missing cap lets water into the flue and the masonry around it, and by the time a stain shows on the ceiling the damage has been working for a while. Our technicians have up to 13 years of experience and install caps and rebuild crowns on these rooftops every working week. We name the materials we use, so you can look up Famco or Copperfield yourself before anyone climbs a ladder. Same-day visits are often possible when you call early. Call (833) 432-4886 for a free estimate.
What Our Chimney Cap & Crown Service Includes
Cap and crown work covers the two parts of a chimney that take the weather head-on: the concrete crown at the top of the masonry, and the cap that sits above the flue. We handle all six of the jobs below, from a straight replacement to a custom fabrication for an odd flue arrangement.
Cap Installation
A chimney cap is the fitted cover that sits over the flue opening on legs or a mesh cage, and it’s the cheapest protection a chimney can get. You need one if the flue is open to the sky, if birds and squirrels have found their way in, or if rain runs straight down the flue every storm. We fit single-flue caps sized to the actual opening, sealed at the base so water sheds away from the masonry rather than behind it.

Cap Replacement
Replacement is for caps that have rusted through, blown loose, or bent out of shape after years of freeze and thaw. A loose cap rattles in wind and eventually lets water run between the cap and the flue, which is worse than having no cap at all. We pull the old unit, check the flue tile for spalling or cracks, and set a new cap with stainless mesh so the next decade of weather doesn’t repeat the problem.

Crown Repair
The crown is the sloped concrete slab at the very top of the chimney, and its whole job is to push water off the brick below. Hairline cracks are normal; missing chunks, a crown pulling away from the flue tile, or a crown that’s gone flat and holds water are not, and each one lets freeze-thaw cycles split the masonry underneath. We rebuild failed crowns with a proper overhang and slope so water leaves the top instead of soaking in.

Crown Coating
Crown coating is a flexible, rubberized membrane rolled over a crown that’s cracked but still structurally sound. It’s the right call when the slab is intact and the damage is surface-level, because it seals the cracks without the cost and disruption of a rebuild. We clean and prep the surface first; coating over dirt or loose concrete is the reason some coatings peel within a season.
Multi-Flue Cap
A multi-flue cap is a single large cover that spans two or more flues sharing one chimney top, common on older Fishtown rowhouses where the original build served a fireplace and a heating flue side by side. Fitting one properly means measuring every flue opening and the whole footprint, then building in enough clearance for each flue to draft. We fabricate these to the chimney rather than forcing a stock size over an uneven top.
Custom Cap
Some chimneys don’t take a standard cap: oversize flues, irregular crowns, or a top that’s been rebuilt at a different height on one side. A custom cap is made to the measured dimensions, which matters because a poor fit lets wind-driven rain in at the edges and can restrict draft on a wood-burning appliance. We take the measurements on site and have the cap built to them in stainless or copper.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
The caps we install come from makers that chimney professionals specify, not the stamped units sold in big-box aisles. Famco caps are built for a tight, weather-resistant fit and we fit them often on single-flue rowhouse chimneys where the top is a true rectangle. Copperfield-sourced components give us a professional distributor’s line to draw from, which matters when a cap needs a stainless mesh or a mounting frame that will outlast the roof it sits on.
Where a cap sits over a liner, the liner brand matters too. DuraFlex flexible liner systems are what we reach for on the older chimneys around here, because a flexible liner follows the slight bends in a flue that a rigid one can’t. And when a crown has cracked and the flue needs resurfacing at the same time, HeatShield is the ceramic system we use; it’s a product that needs specific training to apply properly. Whether you have Famco, Copperfield, DuraFlex, HeatShield or any other make on your chimney, we can help.
Signs You Need Chimney Cap & Crown Right Now
Most cap and crown failures announce themselves before they turn into a masonry job. Here’s what to watch for from the ground.
- Water stains on the ceiling or chimney breast. A cracked crown or an open flue sends rainwater down the inside of the chimney, where it shows up as a brown ring on plaster days later. Catching it at the stain stage is far cheaper than waiting for the masonry to soften.
- Rust streaks or a tilted cap. Rust running down the cap’s legs or a cap sitting visibly crooked means the fasteners or the metal itself have given out. A tilted cap channels water into the joint at the flue instead of away from it.
- Birds, squirrels or nesting debris in the firebox. An uncapped flue is an open door, and animals nesting in a flue block the draft and leave material that can ignite. If you’ve heard scratching or found debris on the smoke shelf, a cap solves the cause.
- Crumbling concrete or brick spalling at the top. When the crown is shedding pieces or the brick just under it is flaking, water is getting in and freezing. This is the stage where crown repair still works and a rebuild is not yet needed.
- A draft that’s gotten worse or smoke that rolls back. A damaged cap, a crushed mesh cage or a cap installed with too little clearance will choke the flue. Poor draft on a wood fire also means smoke and carbon monoxide have somewhere other than up to go.
Our Chimney Cap & Crown Process – Step by Step
Cap and crown work happens at height, on a roof, above a flue. We don’t hand out do-it-yourself steps for it, and we’d rather you didn’t climb up there. Here’s what the job looks like when we do it.
- 1
We look at the whole chimney, not just the cap. The technician checks the crown, the flue tile, the brickwork below the crown and the flashing at the roof line. A cap that gets replaced while the crown underneath is failing just hides the real problem.
- 2
We photograph what we find and show you. Nothing gets recommended without evidence you can see for yourself. If the crown only needs coating and the cap is fine, we say so, and we tell you plainly when a job can safely wait until next season.
- 3
We measure the flue and the crown before ordering anything. Cap sizes are set by the actual flue opening and the chimney’s footprint, not guessed from the ground. For a multi-flue or custom cap, the measurements go to the fabricator and the cap is built to them.
- 4
We prep and set the crown first, then the cap. Cracked crowns get cleaned back to sound concrete and rebuilt or coated with the correct slope and overhang. The new cap goes on last, sealed at the base with stainless mesh where the flue needs it.
- 5
We walk you through the finished work and leave the photos with you. You get a record of what was there before and what’s there now. Your written estimate sets the price, and the sweep or repair work booked at the same visit is agreed before we start.
Because we cover the whole chimney, a chimney repair found during a cap visit doesn’t mean calling someone else to finish the job. And if it’s been a while since the flue was cleaned, a chimney sweep at the same appointment saves a second trip up the roof.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Fishtown?
Prices below are typical estimates for this area; the written estimate you get on site sets the final number.
| Job | Typical estimated range |
|---|---|
| Single-flue cap installation (stock size) | $150 – $400 |
| Cap replacement, including removal of the old unit | $200 – $450 |
| Multi-flue cap, fabricated to measured dimensions | $450 – $1,100 |
| Custom stainless or copper cap | $600 – $1,400 |
| Crown coating (sound crown, surface cracks) | $250 – $550 |
| Crown repair or rebuild | $400 – $1,200 |
What moves the number: the size and number of flues, whether the cap is stock or fabricated, the metal you choose (stainless lasts longer than galvanized and copper costs more than both), and how much of the crown needs rebuilding versus coating. Access matters too, since a chimney tucked against a steep rowhouse roof takes more setup than one with a clear approach.
How to avoid overpaying: get the crown and flue assessed before agreeing to a cap, so you’re not paying twice. Ask what metal the cap is made from and who makes it. And don’t accept a crown rebuild when a coating will do, or a coating when the slab is already failing. Our estimate is free, camera inspection and photo report included, and the flat price is agreed before booking.
Chimney Cap & Crown Near Fishtown – Our Service Area
We work across Fishtown and the neighborhoods around it, including Kensington, Port Richmond, Northern Liberties and Hunting Park, and out through Delaware County to Aldan, Sharon Hill, Collingdale, Clifton Heights, Drexel Hill, Colwyn and Haverford College. Rooftop access and traffic decide how quickly a technician reaches you; a call in the morning is usually the best way to get an early slot. We answer 24/7 and dispatch from 7am to 7pm, Sunday through Friday. Our chimney cap & crown service covers the towns west of the city, and chimney cap & crown work in Sharon Hill follows the same process.
Serving Fishtown, PA – Our Local Coverage Area
We serve Fishtown and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Fishtown
A chimney cap is the cover over the flue opening, and the crown is the sloped concrete slab at the top of the masonry. The crown pushes rainwater off the brick below; the cap keeps rain, animals and stray sparks out of the flue. Together they’re the first line of defense for the whole chimney. If either is missing or failing, water gets into the system and masonry damage follows.
Most single-flue cap installations take under two hours, and a crown coating or repair usually runs half a day. A custom or multi-flue cap needs a second visit because it’s fabricated to your measurements after the first. We’ll give you the expected schedule when we quote the job, and same-day slots are often available when you call early.
A single-flue cap typically runs $150 – $400, a crown coating $250 – $550, and a crown rebuild $400 – $1,200, depending on size, metal and access. Custom and multi-flue caps run higher because they’re built to measure. The written estimate is free and sets the final price. Call (833) 432-4886 for an exact quote – estimates are free.
Yes. Famco and Copperfield are among the professional-grade lines we work with, and we service caps and crown work on them as readily as on any other make. We also install DuraFlex liners and use HeatShield ceramic resurfacing where the flue needs it. Whether your chimney carries one of those brands or a different make, we can help.
Same-day visits are often possible when you call early in the day. We’re closed Saturday and open Sunday through Friday, 7am to 7pm. We answer 24/7; a call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
Our work carries a satisfaction guarantee, and the cap or crown itself is covered by the manufacturer’s own warranty on the product. We’ll tell you what that warranty covers and how long it runs before you agree to the job. If something we fitted fails, call us and we’ll come back out to look at it.
Clear the path to the chimney inside the house, and move anything breakable away from the fireplace and the chimney breast in case work dust falls. If you can, have the flue damper open and the firebox empty so the technician can check the flue from below. That’s it. Everything above the roof line is our job.
Schedule Your Chimney Cap & Crown Service in Fishtown Today
Whether a storm took the cap off or the crown has been cracking for years, one call gets it looked at by someone who does this every day. A free estimate includes the camera inspection and photo report, the flat price is agreed before booking, and we’ll tell you honestly if the work can wait. Call (833) 432-4886. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Fishtown.